使用QNX,无法重新配置IP地址问题

中文QNX 讨论: 欢迎大家灌水,讨论有关QNX 问题。

使用QNX,无法重新配置IP地址问题

帖子ARP » 周四 7月 25, 2013 2:53 pm

在使用QNX bsp用在一块I.MX6双核的板子上,可以启动起来,但是网络模块的TCP/IP协议好像有问题,IP地址都不能配置,但是测试过了,用TFTP协议是有效的,不知有人遇到过这种问题不?相关的信息如下,有点多,麻烦遇到过解决了的,出来给小弟一点建议,谢谢!




U-Boot > run bootcmd_test

mmc0 is current device

reading ifs-mx6q-nitrogen.raw

4675768 bytes read in 262 ms (17 MiB/s)

## Starting application at 0×10800000 …

SCU_CONFIG = 00000501, 2 cpus

L2 cache enabled

CPU0: L1 Icache: 1024×32

CPU0: L1 Dcache: 1024×32 WB

CPU0: VFP-d32 FPSID=41033094

CPU0: NEON MVFR0=10110222 MVFR1=01111111

CPU0: 412fc09a: Cortex A9 MPCore rev 10 792MHz

test point1!

test point2!

test point3!

test point4!

test point5!

test point6!

PLL1 – System : 792MHz

PLL2 – System Bus : 528MHz

PLL3 – OTG USB : 480MHz

PLL4 – Audio : 144MHz

PLL5 – Video : 288MHz

PLL7 – Host USB : 480MHz

PLL8 – Enet : 100MHz

IPG clock : 66000000Hz

IPG per clock : 66000000Hz

UART clock : 80000000Hz

CSPI clock : 60000000Hz

AHB clock : 132000000Hz

AXI clock : 198000000Hz

EMI_SLOW clock: 22000000Hz

DDR clock : 396000000Hz

USDHC1 clock : 198000000Hz

USDHC2 clock : 198000000Hz

USDHC3 clock : 198000000Hz

USDHC4 clock : 198000000Hz

ENFC clock : 24000000Hz

decompressing…CPU1: L1 Icache: 1024×32

CPU1: L1 Dcache: 1024×32 WB

CPU1: VFP-d32 FPSID=41033094

CPU1: NEON MVFR0=10110222 MVFR1=01111111

CPU1: 412fc09a: Cortex A9 MPCore rev 10 792MHz

cpu_startnext: cpu1 -> fc409b8c

System page at phys:10017000 user:fc408000 kern:fc408000

Starting next program at vfe04a1ec

cpu_startnext: cpu0 -> fe04a1ec

Welcome to QNX Neutrino 6.5.0 SP1 on the i.mx6Q Nitrogen (ARM Cortex-A9 MPCore)

Starting watchdog…

Starting UART1,3 drivers (/dev/ser1,3)…

Starting I2C1,2,3 driver (/dev/i2c1,2,3)…

Starting SD3 (microSD) memory card driver…

Starting SD4 (microSD) memory card driver…

Path=0 – FREESCALE USDHC

(devf t1::f3s_flash_probe:285) Unable to properly identify any flash devices

Starting SATA driver…

Starting USB host1 and OTG driver (operating in host mode)

Launching devb-umass…

Starting Ethernet driver

Starting Touch Driver

mx6q_nitrogen_tsc2004_dev_reset: Unable to communicate with touchscreen – 5 —- not connect any touchscreen

Error: unable to reset module dev1

Unable to access “/dev/devi” (2)

# ifconfig

lo0: flags=8049 mtu 33192

inet 127.0.0.1 netmask 0xff000000

fec0: flags=8803 mtu 1500

address: 00:19:b8:01:15:b0

media: Ethernet none ————–not display the network state

# ifconfig fec0 192.168.1.3 netmask 255.255.255.0 ————– try to config IP address to 192.168.1.3

# ifconfig

lo0: flags=8049 mtu 33192

inet 127.0.0.1 netmask 0xff000000

fec0: flags=8803 mtu 1500

address: 00:19:b8:01:15:b0

media: Ethernet none ————-but the IP address configuration not work

#
ARP
New Member
 
帖子: 5
注册: 周四 7月 25, 2013 11:41 am

回到 四海同心QNX论坛

在线用户

正在浏览此版面的用户:没有注册用户 和 1 位游客

cron