Skip navigation.
Home
The QNX Community Portal

View topic - Dual CPU

Dual CPU

Read-only archive of qnx.evaluation (Evaluation) at inn.qnx.com

Dual CPU

Postby Sverre » Sun Jul 02, 2006 9:56 pm

I've tried to install QNX 6.3.0 on a 2X1Ghz PIII computer, but it only
reports one cpu. Are there anyone who can tell me how to enabe support for
both cpu ? I thought that this version had "built in" suport for 2 cpu
(SMP). I have tried 6.1 and 6.2 also, but hav understood that i had to
compile a new kernel. Unfornatly i dont know how to do that, at least not
yet.

Best regards
Sverre
Sverre
 

Re: Dual CPU

Postby Mario Charest » Mon Jul 03, 2006 12:15 pm

"Sverre" <sverreb@iname.com> wrote in message
news:e89fbe$b7c$1@inn.qnx.com...
I've tried to install QNX 6.3.0 on a 2X1Ghz PIII computer, but it only
reports one cpu. Are there anyone who can tell me how to enabe support
for
both cpu ? I thought that this version had "built in" suport for 2 cpu
(SMP). I have tried 6.1 and 6.2 also, but hav understood that i had to
compile a new kernel. Unfornatly i dont know how to do that, at least not
yet.

Copy /boot/fs/qnxbasesmp.ifs to /.boot and reboot.

Best regards
Sverre

Mario Charest
 

Re: Dual CPU

Postby Sverre » Mon Jul 03, 2006 11:14 pm

Than you wery much. It's working, it's realy nice to watch more than one
cpu working.
Is it done the same way with earlyer version

Sverre


"Mario Charest" <postmaster@127.0.0.1> skrev i melding
news:e8b1lq$e5e$1@inn.qnx.com...
"Sverre" <sverreb@iname.com> wrote in message
news:e89fbe$b7c$1@inn.qnx.com...
I've tried to install QNX 6.3.0 on a 2X1Ghz PIII computer, but it only
reports one cpu. Are there anyone who can tell me how to enabe support
for
both cpu ? I thought that this version had "built in" suport for 2 cpu
(SMP). I have tried 6.1 and 6.2 also, but hav understood that i had to
compile a new kernel. Unfornatly i dont know how to do that, at least
not
yet.

Copy /boot/fs/qnxbasesmp.ifs to /.boot and reboot.


Best regards
Sverre



Sverre
 

Re: Dual CPU

Postby Mario Charest » Tue Jul 04, 2006 12:09 pm

"Sverre" <sverreb@iname.com> wrote in message
news:e8c8a4$8el$1@inn.qnx.com...
Than you wery much. It's working, it's realy nice to watch more than one
cpu working.
Is it done the same way with earlyer version

Yes. With earlier version you could rebuild the image though. 6.3 doesn't
come with the SMP kernel as it's part of a TDK.

Sverre


"Mario Charest" <postmaster@127.0.0.1> skrev i melding
news:e8b1lq$e5e$1@inn.qnx.com...

"Sverre" <sverreb@iname.com> wrote in message
news:e89fbe$b7c$1@inn.qnx.com...
I've tried to install QNX 6.3.0 on a 2X1Ghz PIII computer, but it only
reports one cpu. Are there anyone who can tell me how to enabe
support
for
both cpu ? I thought that this version had "built in" suport for 2 cpu
(SMP). I have tried 6.1 and 6.2 also, but hav understood that i had to
compile a new kernel. Unfornatly i dont know how to do that, at least
not
yet.

Copy /boot/fs/qnxbasesmp.ifs to /.boot and reboot.


Best regards
Sverre





Mario Charest
 


Return to qnx.evaluation

Who is online

Users browsing this forum: No registered users and 1 guest

cron