Skip navigation.
Home
The QNX Community Portal

View topic - QNX 6.5.0, CP308, HDA

QNX 6.5.0, CP308, HDA

Discussion about the QNX6 OS.

QNX 6.5.0, CP308, HDA

Postby qnxloader » Mon Jul 25, 2011 12:54 pm

Hi All.
We buy "CP308 multimedia" and have problem with running deva-ctrl-intel_hda:

sloginfo say, that (subsystem ID) not supported
On DELL notebook, with same chip(vid/did) all working fine.
This is output of pci -vvv for audio:

DELL:
Class = Multimedia (RAM)
Vendor ID = 8086h, Intel Corporation
Device ID = 293eh, 82801I (ICH9 Family) HD Audio Controller
PCI index = 0h
Class Codes = 040300h
Revision ID = 2h
Bus number = 0
Device number = 27
Function num = 0
Status Reg = 10h
Command Reg = 106h
I/O space access disabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Error Response disabled
Data/Address stepping disabled
SERR# driver enabled
Fast back-to-back transactions to different agents disabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 10h un-cacheable
PCI Mem Address = f6afc000h 64bit length 16384 enabled
Subsystem Vendor ID = 1028h
Subsystem ID = 263h
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = INT A
Interrupt line = 5
CPU Interrupt = 5h
Capabilities Pointer = 50h
Capability ID = 1h - Power Management
Capabilities = c842h - 0h
Capability ID = 5h - Message Signaled Interrupts
Capabilities = 80h - 0h
Capability ID = 10h - PCI Express
Capabilities = 91h - 10000000h
Device Dependent Registers:
0x040: 0100 0007 0000 0000 0000 0000 0000 0000
0x050: 0160 42c8 0000 0000 0000 0000 0000 0000
0x060: 0570 8000 0000 0000 0000 0000 0000 0000
0x070: 1000 9100 0000 0010 0008 1000 0000 0000
0x080: 0000 0000 0000 0000 0000 0000 0000 0000
...
0x0c0: 0004 0001 0000 0000 3100 a302 0000 0000
0x0d0: 6100 a302 0000 0000 0000 0000 0000 0000
0x0e0: 0000 0000 0000 0000 0000 0000 0000 0000
0x0f0: 0000 0000 0000 0000 860f 0300 0000 0000

CP308
Class = Multimedia (RAM)
Vendor ID = 8086h, Intel Corporation
Device ID = 293eh, 82801I (ICH9 Family) HD Audio Controller
PCI index = 0h
Class Codes = 040300h
Revision ID = 3h
Bus number = 0
Device number = 27
Function num = 0
Status Reg = 10h
Command Reg = 6h
I/O space access disabled
Memory space access enabled
Bus Master enabled
Special Cycle operations ignored
Memory Write and Invalidate disabled
Palette Snooping disabled
Parity Error Response disabled
Data/Address stepping disabled
SERR# driver disabled
Fast back-to-back transactions to different agents disabled
PCI INTx enabled
Header type = 0h Single-function
BIST = 0h Build-in-self-test not supported
Latency Timer = 0h
Cache Line Size= 10h un-cacheable
BAR - 0 [Mem] = d0700000h 64bit length 16384 enabled
Subsystem Vendor ID = 8086h
Subsystem ID = 293eh
Max Lat = 0ns
Min Gnt = 0ns
PCI Int Pin = INT A
Interrupt line = 5
CPU Interrupt = 5h
Capabilities Pointer = 50h
Capability ID = 1h - Power Management
Capabilities = c842h - 0h
Capability ID = 5h - Message Signaled Interrupts
Capabilities = 80h - 0h
Capability ID = 10h - PCI Express
Capabilities = 91h - 10000000h
Device Dependent Registers:
0x040: 0100 0007 0000 0000 0000 0000 0080 0000
0x050: 0160 42c8 0000 0000 0000 0000 0000 0000
0x060: 0570 8000 0000 0000 0000 0000 0000 0000
0x070: 1000 9100 0000 0010 0008 1000 0000 0000
0x080: 0000 0000 0000 0000 0000 0000 0000 0000
...
0x0c0: 0004 0001 0000 0000 3100 a302 0000 0000
0x0d0: 6100 a302 0000 0000 0000 0000 0000 0000
0x0e0: 0000 0000 0000 0000 0000 0000 0000 0000
0x0f0: 0000 0000 0000 0000 860f 0400 0000 0000

Thanks for any suggestion of resolving this problem.
qnxloader
Senior Member
 
Posts: 206
Joined: Mon Oct 06, 2003 8:29 am

RE: QNX 6.5.0, CP308, HDA

Postby maschoen » Tue Jul 26, 2011 3:50 am

Is the subsystem (293eh) the same on the working system?
maschoen
QNX Master
 
Posts: 2640
Joined: Wed Jun 25, 2003 5:18 pm

RE: QNX 6.5.0, CP308, HDA

Postby qnxloader » Tue Jul 26, 2011 4:31 am

No, on working system Subsystem ID = 263h (look output pci -vvv for DELL on first topic)
qnxloader
Senior Member
 
Posts: 206
Joined: Mon Oct 06, 2003 8:29 am

RE: QNX 6.5.0, CP308, HDA

Postby maschoen » Tue Jul 26, 2011 6:32 am

Well the driver thinks this is a problem. Sometimes it is and sometimes it isn't. You need to either get ahold of the driver source, or contact someone at QNX about the problem. If you don't have a service contact, you will probably not get very prompt service.
maschoen
QNX Master
 
Posts: 2640
Joined: Wed Jun 25, 2003 5:18 pm


Return to QNX6 - OS

Who is online

Users browsing this forum: No registered users and 1 guest