Dual CPU

bridged with qnx.evaluation
Post Reply
Sverre

Dual CPU

Post by Sverre » Sun Jul 02, 2006 9:56 pm

I've tried to install QNX 6.3.0 on a 2X1Ghz PIII computer, but it only
reports one cpu. Are there anyone who can tell me how to enabe support for
both cpu ? I thought that this version had "built in" suport for 2 cpu
(SMP). I have tried 6.1 and 6.2 also, but hav understood that i had to
compile a new kernel. Unfornatly i dont know how to do that, at least not
yet.

Best regards
Sverre

Mario Charest

Re: Dual CPU

Post by Mario Charest » Mon Jul 03, 2006 12:15 pm

"Sverre" <sverreb@iname.com> wrote in message
news:e89fbe$b7c$1@inn.qnx.com...
I've tried to install QNX 6.3.0 on a 2X1Ghz PIII computer, but it only
reports one cpu. Are there anyone who can tell me how to enabe support
for
both cpu ? I thought that this version had "built in" suport for 2 cpu
(SMP). I have tried 6.1 and 6.2 also, but hav understood that i had to
compile a new kernel. Unfornatly i dont know how to do that, at least not
yet.
Copy /boot/fs/qnxbasesmp.ifs to /.boot and reboot.
Best regards
Sverre

Sverre

Re: Dual CPU

Post by Sverre » Mon Jul 03, 2006 11:14 pm

Than you wery much. It's working, it's realy nice to watch more than one
cpu working.
Is it done the same way with earlyer version

Sverre


"Mario Charest" <postmaster@127.0.0.1> skrev i melding
news:e8b1lq$e5e$1@inn.qnx.com...
"Sverre" <sverreb@iname.com> wrote in message
news:e89fbe$b7c$1@inn.qnx.com...
I've tried to install QNX 6.3.0 on a 2X1Ghz PIII computer, but it only
reports one cpu. Are there anyone who can tell me how to enabe support
for
both cpu ? I thought that this version had "built in" suport for 2 cpu
(SMP). I have tried 6.1 and 6.2 also, but hav understood that i had to
compile a new kernel. Unfornatly i dont know how to do that, at least
not
yet.

Copy /boot/fs/qnxbasesmp.ifs to /.boot and reboot.


Best regards
Sverre



Mario Charest

Re: Dual CPU

Post by Mario Charest » Tue Jul 04, 2006 12:09 pm

"Sverre" <sverreb@iname.com> wrote in message
news:e8c8a4$8el$1@inn.qnx.com...
Than you wery much. It's working, it's realy nice to watch more than one
cpu working.
Is it done the same way with earlyer version
Yes. With earlier version you could rebuild the image though. 6.3 doesn't
come with the SMP kernel as it's part of a TDK.
Sverre


"Mario Charest" <postmaster@127.0.0.1> skrev i melding
news:e8b1lq$e5e$1@inn.qnx.com...

"Sverre" <sverreb@iname.com> wrote in message
news:e89fbe$b7c$1@inn.qnx.com...
I've tried to install QNX 6.3.0 on a 2X1Ghz PIII computer, but it only
reports one cpu. Are there anyone who can tell me how to enabe
support
for
both cpu ? I thought that this version had "built in" suport for 2 cpu
(SMP). I have tried 6.1 and 6.2 also, but hav understood that i had to
compile a new kernel. Unfornatly i dont know how to do that, at least
not
yet.

Copy /boot/fs/qnxbasesmp.ifs to /.boot and reboot.


Best regards
Sverre





Post Reply

Return to “qnx.evaluation”